FAQ's
E120 - Q. Can I use Google Home Mini to cast direct to the system using voice?
Answer: Yes, we have carried out testing with Google Home Mini which pairs and connects, it will bring the E120 out of standby when a successful connection is made.
E120 - Q. Can I use a subwoofer with this system?
Answer: E120 can be used with speakers and a subwoofer. You will need an amplified subwoofer with a gain and crossover control, most powered subwoofers will have this, and all Q Acoustics powered models have these facilities. You will need an ...
E120 - Q. Can I use more than one pair of loudspeakers with E120?
Answer: E120 has been specifically designed and tested to support powering two pairs of recommended QI65C ceiling speakers, or other 6-8 ohm rated speakers. You should wire the two speakers in series as shown in the diagram below to ensure a reliable ...
E120 - Q. I had/have a Systemline E100, can I use the existing wiring?
Answer: Changing an E100 system to E120 is very easy as E120 fits into the same back box as E100 and uses the same connections for speakers and line auxiliary input. You will however need a small adaptor for the power supply, as E120 uses a slightly ...
Qi50CW - Q. What material are the drivers made from?
Answer: The 5.25" woofer is Polypropylene with rubber surround, and the 0.75" tweeter is polyethylenimine PEI.
Q Install - Q. What does the +/- 3.0dB switch do at the rear of the speaker?
Answer: The switch on the rear allows you to increase or decrease the high frequencies of the loudspeaker, rather than changing the overall signal gain, which is what the receiver enables you to do. It's normally used when speakers are installed ...
Q Install - Q. How do I use the Q Install Fire & Acoustic Hoods?
Answer: When installing in-ceiling loudspeakers with our fire & acoustics hoods, you can either feed the speaker cable between the gaps under the hood when it is in the ceiling void, or alternatively if you would rather feed the cable through the top ...
Q Install - Q. Which of your Q Acoustics in-ceiling speakers provides the widest dispersion?
Answer: Our Q Install Performance range feature larger tweeters compared to our other ceiling speakers, which help to provide wide dispersion, the stereo consisting of two of these larger tweeters, the tweeters themselves can also be pivoted to widen ...
Q Install - Q. Which paint type can I safely use on my Q Acoustics Q Install loudspeaker grilles?
Answer: Whilst we are not in a position to make recommendations about which specific paint to use as there are so many different brands and types out there, we advise that the grilles should be keyed firstly using a fine sand paper, then spray ...
Q Install - Q. What is the maximum thickness of ceiling that the Q Acoustics in-ceiling range can be installed in to?
Answer: The maximum thickness would be 25mm which would allow for proper engagement of the dog-leg clamp.
Q Install - Q. Which Q Acoustics speakers can be used for Dolby Atmos height channels?
Answer: Q Install Performance speakers are just right for Dolby Atmos, The dimension of height & hearing sounds coming from above you is key to the multidimensional Dolby Atmos experience, and although we don’t support the concept of upward firing ...
Q Install - Q. Can I use Professional & Performance ceiling speakers in my bathroom?
Answer: All Q Acoustics Install models are moisture-proof, however, we do have specialist weatherproof models for outdoor/indoor use where an IPX rating is required ;stainless steel fixings and corrosion resistant aluminium grilles are used, together ...
Q Install - Q. What is the specified temperature range of Q Install weatherproof speakers?
Answer: The useable temperature range of the Q Install weatherproof product range is -20°C to +80°C. Humidity should not be an issue due to the IPx4 rating and provided that port bungs are used on Qi45EW and Qi65EW as stated within their user manual.
Q Install - Q. Can I connect my QI-SUB80SP in-wall/in-ceiling subwoofer directly to an AV Receivers subwoofer/LFE out?
Answer: No, there needs to be an intermediate amplifier, a simple low cost 50W - 100W power amplifier could be used.